dd is a command on Unix computer systems part of the Single UNIX Specification. It is used to read and write code to disks.The dd program can also perform conversions on the data as it is copied, including byte order swapping and conversion to and from the ASCII and EBCDICtext encodings. By default, dd reads from STDIN and writes to STDOUT, but these can be changed by using the if (input file) and of (output file) options.

NAME

dd - convert and copy a file

SYNOPSIS

dd [OPERAND]...

dd OPTION

DESCRIPTION

Copy a file, converting and formatting according to the operands.

OPTIONS

bs=BYTES

read and write up to BYTES bytes at a time

cbs=BYTES

convert BYTES bytes at a time

conv=CONVS

convert the file as per the comma separated symbol list

count=N

copy only N input blocks

ibs=BYTES

read up to BYTES bytes at a time (default: 512)

if=FILE

read from FILE instead of stdin

iflag=FLAGS

read as per the comma separated symbol list

obs=BYTES

write BYTES bytes at a time (default: 512)

of=FILE

write to FILE instead of stdout

oflag=FLAGS

write as per the comma separated symbol list

seek=N skip N obs-sized blocks at start of output

skip=N skip N ibs-sized blocks at start of input

status=WHICH

WHICH info to suppress outputting to stderr; 'noxfer' suppresses

transfer stats, 'none' suppresses all

N and BYTES may be followed by the following multiplicative suffixes: c

=1, w =2, b =512, kB =1000, K =1024, MB =1000*1000, M =1024*1024, xM =M

GB =1000*1000*1000, G =1024*1024*1024, and so on for T, P, E, Z, Y.

Each CONV symbol may be:

ascii from EBCDIC to ASCII

ebcdic from ASCII to EBCDIC

ibm from ASCII to alternate EBCDIC

block pad newline-terminated records with spaces to cbs-size

unblock

replace trailing spaces in cbs-size records with newline

lcase change upper case to lower case

ucase change lower case to upper case

sparse try to seek rather than write the output for NUL input blocks

swab swap every pair of input bytes

sync pad every input block with NULs to ibs-size; when used with

block or unblock, pad with spaces rather than NULs

excl fail if the output file already exists

nocreat

do not create the output file

notrunc

do not truncate the output file

noerror

continue after read errors

fdatasync

physically write output file data before finishing

fsync likewise, but also write metadata

Each FLAG symbol may be:

append append mode (makes sense only for output; conv=notrunc sug‐

gested)

direct use direct I/O for data

DD COMMANDS

copy

Clone one partition to another partition

Sda2 and sdb2 are partitions. You want to duplicate sda2 to sdb
Code:

dd if=/dev/sda2 of=/dev/sdb2 bs=4096 conv=notrunc,noerro

If sdb2 doesn't exist, dd will start at the beginning of the disk, and create it. Be careful with order of if and of. You can write a blank disk to a good disk if you get confused. If you duplicate a smaller partition to a larger one, using dd, the larger one will now be formatted the same as the smaller one. And there will be no space left on the drive. The way around this is to use
Code:
rsync
, as described below.

To make an iso image of a CD

This duplicates sector for sector. MyCD.iso will be a hard disk image file of the CD
Code:

dd if=/dev/hdc of=/home/sam/myCD.iso
bs=2048 conv=sync,notrunc

You can mount the image like this:
mkdir /mnt/myCD
mount -o loop /home/sam/myCD.iso /mnt/myCD
This will make the CD root directory the working directory, and display the CD root directory.
Code:
cd /mnt/myCD

Clone a floppy disk to hard drive image file

dd if=/dev/fd0 of=/home/sam/floppy.image

If you're concerned about spies taking the platters out of your hard drive, and scanning them using superconducting quantum-interference detectors, you can always add a "for" loop for US Government DoD approved secure hard disk erasure. Copy and paste the following two lines into a text editor.
Code:

#!/bin/bash
for n in `seq 7`; do dd if=/dev/urandom of=/dev/sda bs=8b conv=notrunc; done

Save the file as anti_scqid.
Code:

chmod +x anti_swqid

Don't run the program until you want to wipe the drive.

Best Laptop Backup: Purchase a laptop drive and an USB 2.0 drive enclosure (Total cost $100.00USD). Assemble the lappy drive into the external enclosure. Plug the external drive into the lappy USB port, and boot with The Knoppix live CD. Launch a terminal. This command will backup the existing drive:
Code:

dd if=/dev/hda of=/dev/sda bs=64k conv=notrunc,noerror

This command will restore from the USB drive to the existing drive:
Code:

dd if=/dev/sda of=/dev/hda bs=64k conv=notrunc,noerror

If the existing disk fails, you can boot from the external drive backup and have your system back instantaneously.

This series will make a DVD backup of hard drive partition:
Code:

dd if=/dev/hda3 of=/home/sam/backup_set_1.img bs=1M count=4430
dd if=/dev/hda3 skip=4430 of=/home/sam/backup_set_2.img bs=1M count=4430
dd if=/dev/hda3 skip=8860 of=/home/sam/backup_set_3.img bs=1M count=4430

And so on. This series will burn the images to DVD+/-R/RW:
Code:

wodim -dev=/dev/hdc --driveropts=burnfree /home/sam/backup_set_1.img

and so forth. To restore the from the backup, load the DVDs in order, and use commands like these:
Code:

dd if=/media/dvd/backup_set_1.img of=/dev/hda3 bs=1M conv=sync,noerror

Load another DVD
Code:

dd if=/media/dvd/backup_set_2.img of=/dev/hda3 seek=4430 bs=1M conv=sync,noerror

Load another DVD
Code:

dd if=/media/dvd/backup_set_3.img of=/dev/hda3 seek=8860 bs=1M conv=sync,noerror

and so forth.

If you wrote chat messages and emails to another girl, on your girlfriend's computer, you can't be sure the files you deleted are unrecoverable. But you can make sure if anyone were to recover them, that you wouldn't get busted.
Code:

dd if=/dev/sda | sed 's/Wendy/Janet/g' | dd of=/dev/sda

Where every instance of Wendy is replaced by Janet, over every millimeter of disk. I picked names with the same number of characters, but you can pad a smaller name with blanks.

wiping overwrite with zeroes

dd if=/dev/zero of=/dev/sda bs=4k conv=notrunc
I just want to make sure my drive is really zeroed out!!
Code:
dd if=/dev/sda | hexdump -C | grep [^00]
return output of every nonzero byte on the drive

dd statistics

/bin/dd if=/dev/zero of=/dev/null count=100MB
When you want to know how far dd has gotten throwing 100MB of 512 byte blocks of zeroes into digital hell, open another terminal and do:
ps aux | awk '/bin\/dd/ && !/awk/ {print $2}' | xargs kill -s USR1 $1

In the terminal running the dd command you will find something like this:

33706002+0 records in

33706002+0 records out

17257473024 bytes (17 GB) copied, 34.791 s, 496 MB/s If you enter the command again, you see more statistics:

58596452+0 records in

58596452+0 records out

30001383424 bytes (30 GB) copied, 60.664 s, 495 MB/s and so on ... Until the command completes

100000000+0 records in

100000000+0 records out

51200000000 bytes (51 GB) copied, 104.193 s, 491 MB/s

Scan a dd Bitstream for Viruses and Malware:

Code:

dd if=/home/sam/file.file | clamscan -

Windows users will find help in the second post, way at the bottom

FYI: duplicating smaller partition or drive to larger partition or drive; or vice versa:

Code:

rsync -avH --exclude=/other_mount_point/ /mount_point/* /other_mount_point/

You want to duplicate the root directory tree to another drive, but the other drive is larger. If you use dd, you will get a file system that is smaller then the larger destination drive. To duplicate files, not the file system: Format and mount the destination drive. Rsync will duplicate the files as files:
Code:

rsync -avH --exclude=/mnt/destination_drive/ /* /mnt/destination_drive/

You need to run:
Code:

grub-install
update-grub

from a the rescue menu of an installation CD/DVD for the target to become bootable. If target was previously bootable, it remains bootable.

Making a NTFS partition, is not easy without using Windows based tools. I was formatting an external drive for my brother, who uses MS Windows XP. I wasn't going to admit Linux couldn't make a NTFS partition.

Make an ext3 partition on the drive. Open a hex editor and make a file containing
Code:
07
Save the file as file.bin. Change the ext3 partition to NTFS:
Code:
dd if=/home/sam/file.bin of=/dev/sdb bs=1 seek=450 count=1
Will change the partition type byte at offset
Code:
0x1c2
from Linux type:
Code:
0x83
, to NTFS type:
Code:
0x07
Please use a drive without important data on it. And, If you use a text editor to make the binary 07 file, you will ruin the existing partition table, because ascii 07 is two hexadecimal bytes (0x3037).
The four primary partition type byte offsets are:
Code:
0x1c2=450
0x1d2=466
0x1e2=482
0x1f2=498
If the dd seek= parameter is changed from 450 to a one of the other values, it will change partition (hd0,1), (hd0,2), or (hd0,3) to NTFS type, rather than partition (hd0,0).
To be revised at a later date:
To make a bootable flash drive: Download 50 MB Debian based distro here:
http://sourceforge.net/projects/insert/
Plug in the thumb drive into a USB port. Do:
Code:
dmesg | tail
Look where the new drive is, sdb1, or something similar. Do:
Code:
dd if=/home/sam/insert.iso of=/dev/sdb ibs=4b obs=1b conv=notrunc,noerror

Set the BIOS to USB boot, and boot.
End to be revised
This command will duplicate the MBR and boot sector of a floppy disk to hard drive image:
Code:
dd if=/dev/fd0 of=/home/sam/MBRboot.image bs=512 count=2
To clone an entire hard disk. /dev/sda is the source. /dev/sdb is the target:
Code:
dd if=/dev/sda of=/dev/sdb bs=4096 conv=notrunc,noerror
Do not reverse the intended source and target. It happens once in a while, especially to the inexperienced user. Notrunc means 'do not truncate the output file'. Noerror means to keep going if there is an error. Dd normally terminates on any I/O error.
Duplicate MBR, but not partition table. This will duplicate the first 446 bytes of the hard drive to a file:
dd if=/dev/sda of=/home/sam/MBR.image bs=446 count=1
If you haven't already guessed, reversing the objects of if and of, on the dd command line, reverses the direction of the write.
To wipe a hard drive: (Boot from a live CD distro to do this.)
Code:
dd if=/dev/zero of=/dev/sda conv=notrunc

This is useful for making the drive like new. Most drives have 0x00h written to every byte, from the factory.

To overwrite all the free disk space on a partition (deleted files you don't want recovered):

Code:
dd if=/dev/urandom of=/home/sam/bigfile.file
When dd ouputs
Code:
no room left on device
all the free space has been overwritten with random characters. Delete the big file with
Code:
rm bigfile.file
Sometimes one wants to look inside a binary file, looking only for clues. The output of the command line:
Code:
less /home/sam/file.bin
is cryptic, because it's binary. For human readable output:
dd if=/home/sam/file.bin | hexdump -C | less
You may also use:
Code:
dd if=/home/sam/file.file | strings -n 8 -t d | less

Recover deleted JPEG files. Look at the header bytes of any JPEG.

Code:
dd if=/home/sam/JPEG.jpg bs=1w count=2 | hexdump -C

The last two bytes are the footer.
Code:

dd if=JPEG.jpg | hexdump -C

Using the JPEG header and footer bytes, search the drive. Command returns the offsets of the beginning and end of each deleted JPEG.
Code:

dd if=/dev/sda3 | hexdump -C | "grep 'ff d8 ff e0' | 'ff d9'"

If
Code:

grep

returned JPEG header bytes at offset:
Code:

0xba0002f

and footer bytes at offset:
Code:

0xbaff02a

Convert the hex offsets to decimal offsets, using one of the many logic capable calculators for Linux. Decimal offsets corresponding to the beginning and end of the JPEG are 195 035 183 and 196 079 658. (196 079 658) - (195 035 183) = rough idea of proper bs= and count= parameters. To find the proper count= figure: (<decinal offset of footer bytes> - <decimal offset of header bytes>) / <block size> = <number of blocks in the deleted JPEG file>. (195 035 183 Ã¯Â¿Â½€“ 196 079 658) = (1 044 475) / (bs=4096) = (254.998). That's really close to 255. If we could land exactly at the header bytes using bs=4096, we could use count=255. But I'm going to use count=257, because random chance dictates the probability of landing dead on the header bytes, using 2^x block size is remote. So we start reading before the header bytes.

We need to use skip= parameter to skip to our start point: 195 035 183 / bs=4096 = 47 616.011. We always round down, so dd will start reading before the beginning of the file. In this case we round down to skip=47615. The following writes a file containing the JPEG with some unwanted bytes before and after.
Code:

dd if=/dev/sda3 skip=47615 of=/home/sam/work_file.bin count=257 bs=4096

This sequence yields the desired JPEG.
Code:

hexdump -C work_file.bin | "grep 'ff d8 ff e0' | 'ff d9'"
dd if=work_file.bin skip=<offset_of_first_header_byte_in_decimal_format> count=<offset_of_last_footer_byte_in_decimal_format +1> - <offset_of_first_header_byte_in_decimal_format> bs=1c of=JPG.jpg

That's the way to get your hands dirty deep in digital data. But this process it automated in the file carving program, foremost.

file carving

two identical drives in every one of my machines. Before I do anything that most probably spells disaster, like an untested command line in a root shell, that contains
Code:
find / -regex ?*.???* -type f | xargs rm -f "$1"
, I do:
Code:
dcfldd if=/dev/sda of=/dev/sdb bs=4096 conv=notrunc,noerror
and duplicate my present working /dev/sda drive system to the /dev/sdb drive. If I wreck the installation on sda, I boot from a live CD distro, and do:
Code:
dd if=/dev/sdb of=/dev/sda bs=4096 conv=notrunc,noerror
And I get everything back exactly the same it was before whatever daring maneuver I was trying didn't work. You can really, really learn Linux this way, because you can't wreck what you have an exact duplicate of. You also might consider making the root partition separate from /home, and make /home big enough to hold the root partition, plus more. Then, To make a backup of root:
Code:
dd if=/dev/sda2 (root) of=/home/sam/root.img bs=4096 conv=notrunc,noerror
To write the image of root back to the root partition, if you messed up and can't launch the X server, or edited /etc/fstab, and can't figure out what you did wrong. It only takes a few minutes to restore a 15 GB root partition from an image file:
Code:
dd if /home/sam/root.img of=/dev/sda2 (root) bs=4096 conv=notrunc,noerror
How to make a swap file, or another swapfile on a running system:
Code:
dd if=/dev/zero of=/swapspace bs=4k count=250000
mkswap /swapspace
swapon /swapspace
This can solve out of memory issues due to memory leaks on servers that cannot easily be rebooted.
How to pick proper block size:
dd if=/dev/zero bs=1024 count=1000000 of=/home/sam/1Gb.file
dd if=/dev/zero bs=2048 count=500000 of=/home/sam/1Gb.file
dd if=/dev/zero bs=4096 count=250000 of=/home/sam/1Gb.file
dd if=/dev/zero bs=8192 count=125000 of=/home/sam/1Gb.file
This method can also be used as a drive benchmark, to find strengths and weaknesses in hard drives:
dd if=/home/sam/1Gb.file bs=64k | dd of=/dev/null
Write:
Code:
dd if=/dev/zero bs=1024 count=1000000 of=/home/sam/1Gb.file
When dd finishes it outputs (total size)/(total time). You get the idea.
Play with 'bs=' and 'count=', always having them multiply out to the same toal size. You can calculate bytes/second like this: 1Gb/total seconds = Gb/s. You can get more realistic results using a 3Gb file.
Rejuvenate a hard drive
To cure input/output errors experienced when using dd. Over time the data on a drive, especially a drive that hasn't been used for a year or two, grows into larger magnetic flux points than were originally recorded. It becomes more difficult for the drive heads to decipher these magnetic flux points. This results in I/O errors. Sometimes sector 1 goes bad, resulting in a useless drive. Try:
Code:
dd if=/dev/sda of=/dev/sda
to rejuvenate the drive. Rewrites all the data on the drive in nice tight magnetic patterns that can then be read properly. The procedure is safe and economical.
Make a file of 100 random bytes:
Code:
dd if=/dev/urandom of=/home/sam/myrandom bs=100 count=1
/dev/random produces only as many random bits as the entropy pool contains. This yields quality randomness for cryptographic keys. If more random bytes are required, the process stops until the entropy pool is refilled (waggling your mouse helps). /dev/urandom does not have this restriction. If the user demands more bits than are currently in the entropy pool, it produces them using a pseudo random number generator. Here, /dev/urandom is the Linux random byte device. Myrandom is a file.

Randomize data over a file before deleting it:
Code:
ls -l
to find filesize.
In this case it is 3769
Code:

ls -l afile -rw------- ... 3769 Nov 2 13:41 <filename>
dd if=/dev/urandom of=afile bs=3769 count=1 conv=notrunc

duplicate a disk partition to a file on a different partition.

Warning!! Do not write a partition image file to the same partition.
Code:

dd if=/dev/sdb2 of=/home/sam/partition.image bs=4096 conv=notrunc,noerror

This will make a file that is an exact duplicate of the sdb2 partition. You can substitue hdb, sda, hda, etc ... OR
Code:

dd if=/dev/sdb2 ibs=4096 | gzip > partition.image.gz conv=noerror

Makes a gzipped archive of the entire partition. To restore use:
Code:

dd if=partition.image.gz | gunzip | dd of=/dev/sdb2

For bzip2 (slower,smaller), substitute bzip2 and bunzip2, and name the file
Code:
< filename >.bz2
.Restore a disk partition from an image file.
Code:
dd if=/home/sam/partition.image of=/dev/sdb2 bs=4096 conv=notrunc,noerror
Convert a file to uppercase:
Code:
dd if=filename of=filename conv=ucase
Make a ramdrive:
The Linux kernel makes a number a ramdisks you can make into ramdrives. You have to populate the drive with zeroes like so:
Code:
dd if=/dev/zero of=/dev/ram7 bs=1k count=16384
Populates a 16 MB ramdisk.
Code:
mke2fs -m0 /dev/ram7 4096
puts a file system on the ramdisk, turning it into a ramdrive. Watch this puppy smoke.
Code:
debian:/home/sam # hdparm -t /dev/ram7
/dev/ram7:
Timing buffered disk reads: 16 MB in 0.02 seconds = 913.92 MB/sec
You only need to do the timing once, because it's cool. Make the drive again, because hdparm is a little hard on ramdrives. You can mount the ramdrive with:
Code:
mkdir /mnt/mem
mount /dev/ram7 /mnt/mem
Now you can use the drive like a hard drive. This is particularly superb for working on large documents or programming. You can duplicate the large file or programming project to the ramdrive, which on my machine is at least 27 times as fast as /dev/sda, and every time you save the huge document, or need to do a compile, it's like your machine is running on nitromethane. The only drawback is data security. The ramdrive is volatile. If you lose power, or lock up, the data on the ramdrive is lost. Use a reliable machine during clear skies if you use a ramdrive.
Duplicate ram memory to a file:
Code:
dd if=/dev/mem of=/home/sam/mem.bin bs=1024
The device
Code:
/dev/mem
is your system memory. You can actually duplicate any block or character device to a file using dd. Memory capture on a fast system, with bs=1024 takes about 60 seconds, a 120 GB HDD about an hour, a CD to hard drive about 10 minutes, a floppy to a hard drive about 2 minutes. With dd, your floppy drive images will not change. If you have a bootable DOS diskette, and you save it to your HDD as an image file, when you restore that image to another floppy it will be bootable.
Dd will print to the terminal window if you omit the
Code:
of=/dev/output
part.
Code:
dd if=/home/sam/myfile

will print the file myfile to the terminal window.

To search the system memory:
Code:

dd if=/dev/mem | strings | grep 'some-string-of-words-in-the-file-you-forgot-to-save-before-the-power-failed'

If you need to cover your tracks quickly, put the following commands in a script to overwrite system ram with zeroes. Don't try this for fun.
Code:
mkdir /mnt/mem
mount -t ramfs /dev/mem /mnt/mem
dd if=/dev/zero > /mnt/mem/bigfile.file
This will overwrite all unprotected memory structures with zeroes, and freeze the machine so you have to reboot (Caution, this also prevents committment of the file system journal, and could trash the file system).

You can get arrested in 17 states for doing this next thing. Make an AES encrypted loop device:
Code:
dd if=/dev/urandom of=/home/sam/aes-drv bs=16065b count=100
modprobe loop
modprobe cryptoloop
modprobe aes
losetup -e aes /dev/loop1 ./aes-drv
password:
mkreiserfs /dev/loop1
mkdir /aes
mount -o loop,encryption=aes,acl ./aes-drv /aes
password:
mv /home/sam/porno /aes
to get the porno on the aes drive image.
Code:
umount /aes
losetup -d /dev/loop1
rmmod aes
rmmod cryptoloop
rmmod loop
to make 'aes-drv' look like a 400 MB file of random bytes. Every time the lo interface is configured using losetup, according to the above, and the file 'aes-drv' is mounted, as above, the porno stash will be accessible in /aes/porno. You don't need to repeat the dd command, OR, the format with reiserfs, OR, the mv command. You only do those steps once. If you forget the password, there is no way to recover it besides guessing. Once the password is set, it can't be changed. To change the password, make a new file with the desired password, and move everything from the old file to the new file. Acl is a good mount option, because it allows use of acls. Otherwise your stuck with u,g,o and rwx.
If you are curious about what might be on you disk drive, or what an MBR looks like, or maybe what is at the very end of your disk:
dd if=/dev/sda count=1 | hexdump -C
Will show you sector 1, or the MBR. The bootstrap code and partition table are in the MBR.
To see the end of the disk you have to know the total number of sectors, and the MAS must be set equal to the MNA. The helix CD has a utility to set this correctly. In the dd command, your skip value will be one less than MNA of the disk. For a 120 GB Seagate SATA drives
Code:

dd if=/dev/sda of=home/sam/myfile skip=234441646 bs=512
So this reads sector for sector, and writes the last sector to myfile. Even with LBA addressing, disks still secretly are read in sectors, cylinders, and heads.
There are 63 sectors per track, and 255 heads per cylinder. There is a total cylinder count. 512_bytes/sector*63_sectors/track*255heads=16065*512bytes/cylinder=8,225,280_bytes/cylinder. 63_sectors/track*255_heads=sectors/cylinder. With 234441647 total sectors, and 16065 sectors per cylinder, you get some trailing sectors which do not make up an entire cylinder: 14593.317584812_cylinders/drive. This leaves 5102 sectors which cannot be partitioned, because to be in a partition you have to be a whole cylinder. It's like having part of a person. That doesn't really count as a person. These become surplus sectors after the last partition. You can't ordinarily read past the last partition. But dd can. It's a good idea to check for anything writing to surplus sectors. For our Seagate 120 GB drive, 234,441,647_sectors/drive - 5102_surplus_sectors = 234,436,545 partitionable sectors.
Code:
dd if=/dev/sda of=/home/sam/myfile skip=234436545
writes the last 5102 sectors to myfile. Launch midnight commander (mc) to view the file. If there is something in there, you do not need it for anything. In this case you would write over it with random characters:
Code:
dd if=/dev/urandom of=/dev/sda bs=512 seek=234436545
Will overwrite the 5102 surplus sectors on our 120 GB Seagate drive.
Block size:
One cylinder in LBA mode = 255_heads*63_sectors/track=16065_sectors=16065*512_bytes=8,225,280_bytes. The b means '* 512'. 32130b represents a two cylinder block size. Cylinder block size always works to cover every sector in a partition, because partitions are made of a whole number of cylinders. One cylinder is 8,225,280 bytes. If you want to check out some random area of the disk:
Code:
dd if=/dev/sda of=/home/sam/myfile bs=4096 skip=2000 count=1000
Will give you 8,000 sectors in myfile, after the first 16,000 sectors. You can open that file with a hex editor, edit some of it, and write the edited part back to disk:
Code:

dd if=/home/sam/myfile of=/dev/sda bs=4096 seek=2000 count=1000
Image a partition to another machine:
On source machine:
Code:
dd if=/dev/hda bs=16065b | netcat < targethost-IP > 1234

On target machine:
Code:
netcat -l -p 1234 | dd of=/dev/hdc bs=16065b
Variations on target machine:
Code:
netcat -l -p 1234 | bzip2 > partition.img
makes a compressed image file using bzip2 compression.
Code:
netcat -l -p 1234 | gzip > partition.img
makes a compressed image file using gzip compression. I back up a 100 GB lappy disk on a desktop drive, over a lan connection, and the 100 GB compresses to about 4.0 GB. Most of the drive is empty, so it's mostly zeroes. Repetitive zeroes compress well.
Alert!! Don't hit enter yet. Hit enter on the target machine. THEN hit enter on the source machine.
Netcat is a program, available by default, on most linux installations. It's a networking swiss army knife. In the preceding example, netcat and dd are piped to one another. One of the functions of the linux kernel is to make pipes. The pipe character looks like two little lines on top of one another, both vertical. Here is how this command behaves: This byte size is a cylinder. bs=16065b equals one cylinder on an LBA drive. The dd command is piped to netcat, which takes as its arguments the IP address of the target(like 192.168.0.1, or any IP address with an open port) and what port you want to use (1234).
You can also use ssh.
Code:
dd if=/dev/sdb2 | ssh sam@192.168.0.121 "sudo dd of=/home/sam/sdb2.img"
Dd is like Symantec Norton Ghost, Acronis True Image, Symantec Drive Image. You can perform disk drive backup, restore, imaging, disk image, cloning, clone, drive cloning, transfer image, transfer data, clone to another drive or clone to another machine, move Windows XP to a new hard drive, clone Windows XP, clone Windows, transfer Windows, hard drive upgrade, duplicate a boot drive, duplicate a bootable drive, upgrade your operating system hard drive, Tired of reinstalling WinXP Windows XP?

How to rescue a CD or DVD, HDD, flash drive or photos:

ddrescue -b 2048 -d -e 20 -r 300 -v /dev/hdc /home/sam/dvd.iso log.txt

If /home/sam/dvd.iso won't mount, carve it:
Code:

foremost -t all -k 256 -v -b 2048 -i ~/dvd.iso -o ~/dvd/

Your files will be in directory: /home/sam/dvd.

MS Windows Section

Use dd for drive cloning, backup, drive upgrading, and restore tasks. Boot a Windows XP machine with a Knoppix Linux live CD. Download Knoppix, burn the iso image file to a CD, boot with it, and clone drives. Drives are described to the dd command using device files. Boot into Knoppix, and open a root shell. It's in the penguin menu. (80 conductor grey ribbon cable) = /dev/hda for master; /dev/hdb for slave. SATA are /dev/sda and /dev/sdb.
The partitions on the first drive:
fdisk -l /dev/hda
The manual page for fdisk:
Code:
man fdisk
Use parted to make partitions:
Code:
man parted
If one has trouble, leave a reply. Knoppix is slow, because it runs on a CD drive (1/1000 the speed of a HDD).
Many games written for Windows are virtually impossible back-up. This leaves only the original media. If it gets damaged, the user SOL. But there is a way to make back-ups using Linux. Download Adrienne Knoppix, and choose the option to copy it to a flash drive. Boot the flash-drive. If there are two optical drives available, load the CD/DVD source disk in one drive, and the blank disk in the other. Open a terminal from the menu, and get the root account by typing
su
Now type
Code:

ls /dev/hd*

If /dev/hdb, /dev/hdc and possibly /dev/hdd come up, these are your optical drives, unless you have (2) ide hard drives. In that instance /dev/hdb would be a hard drive. If nothing comes up, type
Code:

ls /dev/sr*
The possibilities are /dev/sr0 and sr1. If nothing comes up, your optical drive are /dev/scd0 and scd1. After the disks are loaded, type
Code:
wodim dev=/dev/hdc fs=16m speed=8 -raw96r driveropts=noburnfree,hidecdr -dummy -overburn -copy /dev/hdc/
If there are no errors, hit the up arrow, remove '-dummy' and run the command.
Feel free to read the entire posts.
Dd is not presently able to clone Microsoft Windows Vista OEM Partitions.
How to make a bootable CD from a bootable floppy
Put the floppy in the floppy drive, and don't mount it, YET!
Code:
dd if=/dev/fd0 of=/home/sam/floppy.img
Mount /home/sam/floppy.img:
Code:
mkdir /mnt/floppy.img
mount -o loop /home/sam/floppy.img /mnt/floppy.img

Customize the image:
Code:
cd /mnt/floppy.img/
rm <files you don't need>
cp /home/sam/bios.bin

or any other files you want on the CD. But don't exceed the 1.44 MB size of a floppy. Check space left in the mounted image
Code:
df -h

Unmount the floppy image
Code:

cd ..
umount /mnt/floppy.img

Make the .iso CD image file:
Code:

mkisofs -o /home/sam/floppy.img.iso -b /home/sam/floppy.img /home/sam/floppy.img

Burn the iso file to a CD:
Code:

wodim dev=/dev/hdc -sao driveropts=burnfree -dummy /home/sam/floppy.img.iso

This is a dummy burn, with the drive laser off. After you check the dummy run for errors, by looking at the program output, hit the up arrow, delete '-dummy', Enter. If you need a DOS boot floppy image file: [URL]http://www.freedos.org/[URL]

You want to find out if your girlfriend is cheating on you, having cyber whoopie, or your a control freak. Even if the computer is secured with a password, you can boot with the: Knoppix Live CD and search the entire drive partition for text strings:
Code:

dd if=/dev/sda2 bs=16065 | strings -n 10 -t d | grep -i -B 20 -A 20 'luv U'

will search the drive partition specified in the dd command, for the text string specified between the single quotes in the grep command. Searching an entire disk partition several times can be time consuming. You might gift her a day at the spa. Females love that. That would keep her occupied while you invade her privacy. I highly recommend googling: "How can I tell if he's married?". This will produce a list of hits for sites females use to check whether or not their dates are married. You must click the link, go to the site, get the name of the organization running the site, google "<name of organization>", until you find the correct mailing address. Send a letter by certified mail instructing the organization to hereafter refrain from using a certain name for profit, because it doesn't belong to them, and they aren't entitled to profit by using it in a query or search result. State the specific name without a middle initial, and send a copy to any judge, with a cover letter, of course, and the enclosure marked COPY.

This particular command string prints the search results, preceded by the decimal offset of its location on the drive, to the screen. If the offfset is: 34,409,872, we want manageable numbers, custom designed for speed and ease of use. The decimal disk offset is roughly 34 million, so the data we want to view is 34 MB into the partition. We divide 34,409,872 by some power of 2. Experience says 2^13 is about what we want, to get a quotient in the thousands. 34,409,872/8192=~4200. The data we want is 8,192 4,200 byte blocks, OR, 4,200 8,192 byte blocks, into the partition. We check: 4200*8192=34406400; 34,409,872-34406400=3472. This means the following command line will start reading 3,472 bytes before the string location.
Code:

dd if=/dev/sda2 bs=4200 skip=8192 count=2 | strings > file.txt

... and finish reading approximately 4,200 bytes after the string. This will net you 3.4k of disk contents before the search string, and 4.2k after. That's a 7.6k chunk of disk, plenty for what we're doing. With this method you search all the deleted files, any chat activity, Internet temporary files, and emails. It works regardless of what security has been deployed on the machine. It works with NTFS, ext2, ext3, reiserfs, swap, UFS, iso9660, and FAT partitions. But, it is illegal to use this method on a computer you aren't authorized to search. People can be sued, or imprisoned for performing unauthorized searches.

[color="red"]This next thing does not work anymore, because the Linux kernel wised up a bit. I'm working on an alternate method.[color] You can search system memory with this method, by substituting
Code:

/dev/mem

for
Code:

/dev/sda2

.
Write system memory to a CD. This is useful for documenting memory contents without contaminating the HDD. I recommend using a CD-RW so you can practice a little. This doesn't involve dd, but it's cool.
Code:

wodim /dev=/dev/scd0 -raw driveropts=burnfree /dev/mem

to find the cdwriter:
Code:

wodim --devices

This method records raw, so you have to do a:
Code:

dd if=/dev/hdd | hexdump -C | less

to view the recorded memory. You can also employ the string search method above, substituting
Code:

/dev/hdd

for
Code:

/dev/sda2

.
Code:

dd if=/dev/hdd | strings -n 6 -t d | grep 'string'

string is any ascii sequence, hex sequence (must be separated with a space: '55<space>aa<space>09' searches for the hex string '55aa09'),
list:
Code:

'[[:alnum:]]' any alphanumeric characters
'[[:alpha:]]' any alpha character
'[[:digit:]]' any numeric character
'[[:blank:]]' tabs and spaces
'[[:lower:]]' any lower case alpha characters
'[[:upper:]]' any uppercase alpha character
'[[:cntrl:]]' ASCII characters 000 thru 037, and 177 octal
'[[:graph:]]' [:alnum:] and [:punct:]
'[[:punct:]]' any punctuation character ` ! ' # $ % ' ( ) * + - . / : ; < = > ? @ [ \ ] ^ _ { | } ~
'[[:space:]]' tab, newline, vertical tab, form feed, carriage return, and space '[[:xdigit:]]' any hex digit ranges('[a-d]' = any, or all abcd, '[0-9]' = any, or all 0123456789)

Code:

dd if=/dev/sda | hexdump -C | grep '[:punct:]' | less

... will return every line from the
Code:

hexdump -C

output that contains any punctuation characters specified above. It will not gather only punctuation characters.
Back up your MBR:
Code:

dd if=/dev/sda of=mbr.bin count=1

Put this on a floppy you make with:
Code:

dd if=boot.img of=/dev/fd0

I back up floppies to a HDD. Floppies don't last forever, so I do:
Code:

dd if=/dev/fd0 of=/home/sam/floppies/backup.bin conv=notrunc

If my floppy fails, I can make unlimited copies:
Code:

dd if=/home/sam/floppies/backup.bin of=/dev/fd0 conv=notrunc

Here is a command line to read your BIOS, and interfaces:
Code:

dd if=/dev/mem bs=1k skip=768 count=256 2>/dev/null | strings -n 8

dd will not duplicate or erase an HPA, OR, host protected area. Dd will erase a disk completely, but not as well as using the hardware secure erase, security erase unit command
Dd need not be black boxed like other inexpensive forensic software:
http://www.cftt.nist.gov/
For a low cost bootable CD based professional ghosting solution, that supports all operating systems and file systems:
http://www.feyrer.de/g4u/
Variation of dd for data rescue off defective media:
http://www.garloff.de/kurt/linux/ddrescue/
Department of Defense implementation of dd:
http://dcfldd.sourceforge.net/
Sdd is useful when input block size is different than output block size, and will succeed in some instances where dd fails:
http://linux.maruhn.com/sec/sdd.html
This is one of the best links I haven't written about dd:
http://www.softpanorama.org/Tools/dd.shtml

Note that sending a SIGUSR1 signal to a running 'dd' process makes it
print to standard error the number of records read and written so far,
then to resume copying.

Code:

$ dd if=/dev/zero of=/dev/null& pid=$!
$ kill -USR1 $pid; sleep 1; kill $pid

10899206+0 records in 10899206+0 records out

BLOCKS and BYTES may be followed by the following multiplicative suffixes: c 1, w 2, b 512, kB 1000, K 1024, MB 1000*1000, M 1024*1024, GB 1000*1000*1000, G 1024*1024*1024
So,
Code:

dd if=/dev/sda of=/dev/sdb bs=1GB

Will use one gigabyte block sizes.
bs=4b would give dd a block size of 4 disk sectors. 1 sector=512 bytes.
bs=4k would indicate dd use a 4 kilobyte block size. I have found bs=4k to be the fastest for copying disk drives on a modern machine.

OPERANDS The following operands are supported:
Code:

if=file

Specifies the input path. Standard input is the default.
Code:
of=file

Specifies the output path.
Standard output is the default.
seek=blocks Skip this many blocks in the output file.
Code:

ibs=n

Specifies the input block size in n bytes (default is 512).
Code:

obs=n

Specifies the output block size in n bytes (default is 512).
If no conversion other than
Code:

sync, noerror, and, notrunc

is specified, each input block is copied to the output as a single block without aggregating short blocks.
Code:

cbs=n

Specifies the conversion block size for block and unblock in bytes by n (default is 0). If cbs= is omitted or given a value of 0, using
Code:

block or unblock

produces unspecified results. This option is used only if ASCII or EBCDIC conversion is specified.
Code:

ascii and asciib

operands, the input is handled as described for the unblock operand except that characters are converted to ASCII before the trailing SPACE characters are deleted.
Code:

ebcdic, ebcdicb, ibm, and ibmb

operands, the input is handled as described for the block operand except that the characters are converted to EBCDIC or IBM EBCDIC after the trailing SPACE characters are added.
Code:

files=n

Copies and concatenates n input files before terminating (makes sense only where input is a magnetic tape or similar device).
Code:

skip=n

Skips n input blocks (using the specified input block size) before starting to copy. On seekable files, the implementation reads the blocks or seeks past them. On non-seekable files, the blocks are read and the data is discarded.
Code:

iseek=n

Seeks n blocks from beginning of input file before copying (appropriate for disk files, where skip can be incredibly slow).
Code:

oseek=n

Seeks n blocks from beginning of output file before copying.
Code:

seek=n

Skips n blocks (using the specified output block size) from beginning of output file before copying. On non-seekable files, existing blocks are read and space from the current end-of-file to the specified offset, if any, is filled with null bytes. On seekable files, the implementation seeks to the specified offset or reads the blocks as described for non-seekable files.
Code:

count=n

Copies only n input blocks.
Code:

conv=value

[,value. . . ] Where values are comma-separated symbols from the following list:
Code:

conv=notrunc

Do not truncate the output file.
Code:

ascii

Converts EBCDIC to ASCII.
Code:

asciib

Converts EBCDIC to ASCII using BSD-compatible character translations.
Code:

ebcdic

Converts ASCII to EBCDIC. If converting fixed-length ASCII records without NEWLINEs, sets up a pipeline with
Code:

dd conv=unblock

beforehand.
Code:

ebcdicb

Converts ASCII to EBCDIC using BSD-compatible character translations. If converting fixed-length ASCII records without NEWLINEs, sets up a pipeline with
Code:

dd conv=unblock

beforehand.
Code:

ibm

Slightly different map of ASCII to EBCDIC. If converting fixed-length ASCII records without NEWLINEs, sets up a pipeline with dd
Code:

dd conv=unblock

beforehand.
Code:

ibmb

Slightly different map of ASCII to EBCDIC using BSD-compatible character translations. If converting fixed-length ASCII records without NEWLINEs, sets up a pipeline with
Code:

dd conv=unblock

beforehand. The
Code:

ascii (or asciib), ebcdic (or ebcdicb), and ibm (or ibmb)

values are mutually exclusive. block Treats the input as a sequence of NEWLINE-terminated or EOF-terminated variable-length records independent of the input block boundaries. Each record is converted to a record with a fixed length specified by the conversion block size. Any NEWLINE character is removed from the input line. SPACE characters are appended to lines that are shorter than their conversion block size to fill the block. Lines that are longer than the conversion block size are truncated to the largest number of characters that will fit into that size. The number of truncated lines is reported. unblock Converts fixed-length records to variable length. Reads a number of bytes equal to the conversion block size (or the number of bytes remaining in the input, if less than the conversion block size), delete all trailing SPACE characters, and append a NEWLINE character. The block and unblock values are mutually exclusive.
Code:

lcase

Maps upper-case characters specified by the LC_CTYPE keyword tolower to the corresponding lower-case character. Characters for which no mapping is specified are not modified by this conversion.
Code:

ucase

Maps lower-case characters specified by the LC_CTYPE keyword toupper to the corresponding upper-case character. Characters for which no mapping is specified are not modified by this conversion. The lcase and ucase symbols are mutually exclusive.
Code:

swab

Swaps every pair of input bytes. If the current input record is an odd number of bytes, the last byte in the input record is ignored.
Code:

noerror

Does not stop processing on an input error. When an input error occurs, a diagnostic message is written on standard error, followed by the current input and output block counts in the same format as used at completion. If the conversion is specified, the missing input is replaced with null bytes and processed normally. Otherwise, the input block will be omitted from the output. notrunc Does not truncate the output file. Preserves blocks in the output file not explicitly written by this invocation of dd. (See also the preceding
Code:
of=file
operand.)
Code:
sync
Pads every input block to the size of the ibs= buffer, appending null bytes. (If either block or unblock is also specified, appends SPACE characters, rather than null bytes.)
ENVIRONMENT VARIABLES
The following environment variables affect the messages and errors messages of dd:
LANG
Provide a default value for the internationalisation variables that are unset or null
is unset or null, the corresponding value from the implementation-dependent default locale will be used. If any of the internationalisation variables contains an invalid setting, the utility will behave as if none of the variables had been defined.

Code:

LC_ALL

If set to a non-empty string value, override the values of all the other internationalisation variables.

Code:

LC_CTYPE

Determine the locale for the interpretation of sequences of bytes of text data as characters (for example, single- as opposed to multi-byte characters in arguments and input files), the classification of characters as upper- or lower-case, and the mapping of characters from one case to the other.

Code:

LC_MESSAGES

Determine the locale that should be used to affect the format and contents of diagnostic messages written to standard error and informative messages written to standard output.

Code:

NLSPATH

Determine the location of message catalogues for the processing of LC_MESSAGES.

Pages

Saturday, 1 March 2014

DD commands for all type of use